et
et en_GB

Rubin

Rubin – Custom-made metal roofing tiles

RUBIN metal roofing tile, elegance, minimalist embossing. Available in two variants of module length (350 and 400 mm) and break height (stroke) – 15 / 20 mm. Effective width (covering): 1150 mm.

Metal roof tiles with character

The shape of the metal roof tile from start to finish was developed by Pruszyński Sp z o. o. taking into account appropriately high aesthetic values ​​while maintaining excellent operational parameters – the covering width of the sheet is 1150 mm!!!

Technical Specifications

Number of moduleslength of sheet – SZAFIR 350/15length of sheet – SZAFIR 400/20
20,80,9
31,151,3
41,51,7
51,852,1
62,22,5
72,552,9
82,93,3
93,253,7
103,64,1
113,954,5
124,34,9
134,655,30*
145,00*4,7
155,356,1
165,76,5
176,056,9
186,47,3
196,757,7
207,18,1

Transport and storage

  • If the customer collects the product  with his own means of transport, the vehicle shall have an open loading platform allowing for easy loading and unloading, with the length suitable for ordered sheets. The sheets shall not extend beyond the platform. Proper anchoring of the sheet packages for the transport will reduce the damage of the sheet paint coat due to abrasion.
  • It is of course the best to unload in original manufacturer packaging , using mechanical unloading equipment.
  • Unloading shall be carried out by the proper number of people, that is in the case of long sheets (ca. 6  linear metre) the sheets shall be unloaded by 6 people, three on each side. Special attention shall be paid not to friction one sheet against the other, bend the side edges or stretch the sheet. Steel sheet deformation during the unloading and moving can result in problems with proper installation (chinks in clamps).
  • Protective foil is used to safe the roof panels against mechanical damages. It should be removed directly at the assembly stage and it should protect panels against humidity and sun during the storage period. Non compliance with above rules may cause difficulties when removing the foil from sheets and dirty after the glue.

Maintenance and washing

  • In order to extend durability of roofs and elevations it’s recommended to check and conservative it.
  • Inspection – One time a year (it’s best in spring) there should be inspection of roof/elevation in order to early detection of possible damage.
  • Cleaning of steel sheet – Roof and elevation made of steel sheets require cleaning at least once a year. Stratifying dirt on steel sheet may cause uneven discoloration of lacquer (because of uneven impact of UV beams), and lower protection to corrosion(dust traps humidity on steel sheets which causes damage). Dirty and stained spots can be cleaned by soft brush and water (temp. max. 60c). If it is necessary it is permitted to use some light detergent (ph 6/7, max 10% solution). There also can be used pressed water(max. 100bar) to cleaning, however the beam of water cannot be applicated too near of surface of sheets(min. 30 cm), also it shouldn’t be perpendicularly to surface. Near the connections water beam should be directed to bottom, to avoid water of entering cracks near connections. With old surfaces of steel sheets we should deal with high cautiously. Cleaning should be conducted from top to bottom, and cleaned spots should be rinsed out immediately.
  •  It is not permitted to use scouring powders, nitro solvent, chlorine liquor, aromatised substances, substances with Amon chloride or sodium.
  • Damages – Possible damages during guarantee should be consulted with Contractor of roof/elevation and can be repaired only with his written permission.Repair of damages on small surfaces is done with quick-drying varnish. However painting big surfaces should be done with special industrial paints to renovating coverings. Painting should be limited only to special damaged spots (scratches to steel, centres of corrosion etc.)Preparation of surface to painting should be done with generally accepted rules. It is necessary to precisely remove all signs of corrosion – best with special brush or  close-grained sandpaper. Then that surface should be undusted, degreased and cleaned. To degrease extraction naptha or water with addition of surfactant(best with 1-2%solution of ammoniac) can be used. Repaired spots may be different in colour compared to original steel sheets because of natural impact of atmospheric phenomenon (ageing of varnish due to impact of UV radiation)
  • ATTENTION!– During inspecting, cleaning, conservation and repair all work safety regulations should be obeyed.Pruszyński Sp. z o.o. is not in charge of possible accidents during carrying out all following actions.

NAME

  • Marek Magismaa, CTO
  • Ülo Taremaa, CFO
  • Riho Narusk CIO
  • Mati Uuekula CMO

EMAIL

PHONE

Design & Developed by Techsaga Corporations.
Facebook Twitter Instagram Linkedin